2015-EOBDTool.co.uk

12/14/2015

Xhorse VVDI MB BGA Tool VVDI Key Programmer for Mercedes Benz

12/11/2015

How to Install VXDIAG VCX NANO Land Rover and Jaguar V143

How to Use VVDI MB TOOL to Calculate Mercedes BGA Key Password

11/10/2015

Xhorse VVDI 2 update to V1.0.8

Xhorse VVDI2 Commander VAG, Porsche and BMW programmer software is newly released to V1.0.8.

Free download VVDI2 V1.0.8 software

VVDI 2 V1.0.8 update feature:

===== VAG V1.0.8 =====
1. Fix bug for key learn in touareg(KWP2000), bentley(KWP2000)
2. Add support for BFM remote control (car with BFM system, such as polo, jetta etc)
3. Add support for flash programming _E type FRF file
4. Add support for get PIN and CS from cayenne ECU (4th immobilizer, EEPROM 95128)
5. Bugfix
===== BMW V1.0.8 =====
1. Fix bug for file change km (CAS1/CAS2/CAS3)
2. Fix bug for BWM KWP protocol
3. Language fix

===== Transponder Programmer V1.0.8 =====
1. Enhance programmer stability
2. Fix bug for some Koleos 9S12 can't detect key position
3. Bugfix

9/28/2015

Xprog-M Read Mercedes EZS Motorola 912 or 9s12 EEPROM

Here is the detail instruction on reading Mercedes-Benz EZS Motorola 912 or 9s12 CPU EEPROM in-circuit with X-prog M ECU programming tool (xprog V5.0, V5.3, V5.50, V5.55).

Note: you can also use other programmers, like Rosfar, ETL etc.

To read Mercedes EZS 912 CPU EEPROM

Mercedes-Benz EZS Motorola 912 or 9s12 CPU

Almost all control points joined with service connector of EZS – black painted connector. We offer connection cable for EZS reading with X-Prog programmer:

You can make yourself cable for connection with other programmers.

Use the following wiring connection diagram:

1 - EXTAL

2 – GND

3 – RESET

4 – BKGD

The EXTAL signal doesn’t joint to service connector, so we have to make jump according to CPU type. If you see on board

It means you have 912 CPU. Do make a jump like in picture (you can keep this jump even after reading/writing finishing).

Find resistor on RESET line and make a jump on it for good communication. (you can keep this jump even after reading/writing finishing).

Then solder red wire of our cable for power supplying.

Now plug in the connector to Xprog-M ECU programmer board like in picture:

We recommend to mount the part of cover on to the EZS, then you have not a mistake while you connect cable to EZS.

Open Xprog software and press “Device” tab.

Choose the EEPROM Type, 1,2,3 in following

Press “New” button, then press “Read” button to read eeprom

Reading device

You will see the eeprom data

Save EEPROM file you have read

To read Mercedes EZS 9S12 CPU EEPROM

If you see on the board

It means you have 9S12 CPU. Do make only one jump like in picture

Then solder red wire of our cable for power supplying.

Then do the same job like with previous CPU type but remember about a difference when you choose microchip in Xprog programmer software.

Sometimes new board types with 9S12 CPU have not some jumps (it has zero resistance as usual). Make the- se jumps yourself.

You can keep these jumps after reading/writing, too.

9/20/2015

Xhorse VVDI Pro and VVDI2 program Porsche key

2015 Original VVDI2 adds Porsche software function. Here is the step-by-step instruction on programming Porsche key with original Xhorse VVDI2 and VVDI Pro programmer.

Step 1: Read Porsche BCM 2M25J EEPROM with VVDI Prog

This is a Porsche 2M25J BCM

Connect BCM with VVDI Pro

Open VVDI Pro programmer software

Select 4:Immo->Porsche-BCM-2M25J

Click “Connection diagram”

Follow wiring diagram given to connect the BCM with VVDI pro connectors

Close the wiring diagram

Click “New” tab

Hit “Read” to read data

Device initializing

The VVDI pro will prompt the chip is encrypted, you need to decrypt

Click “Remove encrypt” tab

Decrypting chip in progress

Decryption is completed (result will shown on the bottom)

Again click “Read” to read data, wait the procedure process to 100%

Save data (to desktop)

Step 2: Generate Porsche Dealer key with VVDI2

Open VVDI2 software

Select “Key programmer”

Select “Data Processing Device” on the left

Select car Region: Europe-> Vehicle model: Porsche-> BCM type: 2M25J

Click “Load EEPROM” button on right

Load the saved EEPROM data by VVDI Pro

If the system prompt if erase key data, click Yes

Select erase key position “Key 2”, press Next, This will generate a new data file

Save the new data file to desktop

Again click “Load EEPROM” to load the new eeprom file just saved

Click “NO”

Key ID remain key 1

Select “Key 2”, select “Generate Dealer Key”

Click Yes if generate dealer key is done

Again save the data to desktop

Porsche dealer key has been programmed.

VVDI PROG 3.40 Programmer for BMW CAS4+ All Key Lost(Review)

Pleased to share my purchase experience of VVDI PROG Auto Key Programmer. Just got this programmer for a few days from China.(I am Chinese, also)

Package came to London for about 6 days, for €385.

Ps. VVDI PROG 3.40 free download I found:

(software, driver, IMG&Language files...)

https://www.dropbox.com/s/3zdc4ummm7h6xs5/VVDIProg3.4.0.zip?dl=0

And I used this vvdi prog and vvdi2 to do BMW all key lost. Here is the procedure. This vvdi2 is from my friend, sounds from China also.

Step 1: Read CAS4+ 5M48H EEPROM with VVDI PRO

Disassemble the CAS4+ and ECU.

First, read CAS4+ EEPROM data.

Take out the circuit board from CAS4+.

Follow VVDI Pro wiring diagram to connect the cables with circuit board.

Remove 4 components on CAS4 (solder them when finish operation ) and begin wiring connectors

The circuit board after removing 4 components.

Start wiring connection according the wiring diagram..

Then begin to read and write.

Select “BMW CAS4-5M48H” EEPROM

Click “New” and then click “Read”.

Now the equipment is being initialized.

Check the chip type.

Select “Yes” to crack chip.

Cracking the chip...

OK, finish cracking.

Start reading the data.

Finish reading data.

Name the file.

And click “Save”.

Step 2: Read BMW ECU

Disassemble the ECU. Punch a hole here for wire connection.

Follow VVDI 2 wiring diagram to connect the cables with ECU.

Point the boot. Point contact and press it for a while.

Go to the software and select EEPROM.

Click “New”.

Click “Read”.

Well, begin checking this equipment. Device initializing.

Crack the chip.

Click “Yes” to continue.

Finish reading data. ISN is also displayed.

Save data.

Name the new file.

And click “Save”.

Finish data reading.

Step 3: Write key with VVDI 2

Begin to write the key.

(All the data have been read out, so we can begin writing the key.)

Insert the key in VVDI2.

Open VVDI2 software, Quick Start.

Select BMW.

Select “File Make Key”.

Select “5M48H”.

Click “OK”.

Load the data, select the folder “000000000”.

First load BMW CAS4+ data. Click to open.

Select “Key3” and click “Generate Dealer Key”

Click “I have the engine data, click Next to load it”, and click “Next”.

Load the ECU data, “baoma 525ecu.bin”, and click “Open”.

You will prompt that it will take 30 seconds. Click “OK”.

It is generating a key. Wait! Write key success.

Step 4: Test new key

OK, finish writing the key. And now, we go to check it. (click “OK”)

Check if the key can work normally.

Put the key on BMW test platform.

Pay attention to the green light (LED 3).

The green light is lighted, which means the key can work normally.

Then take the key down.

You will see the green light will be off.

Again put the key on BMW test platform.

Key matching is successful.

9/17/2015

Xhorse VVDI 2 user manaul (free download pdf)

2015 Newest VVDI 2 Commander Key Programmer Update Online for VW/Audi/BMW/Porsche:

9/10/2015

How to update VVDI Pro programmer software & firmware?

Xhorse VVDI Pro Programmer has newly updated software to latest V3.4.0 with firmware 1.2.2. (10/09/2015).

Language: English/Chinese

Free download VVDI Prog V3.4.0 software

https://mega.nz/#!fpFjlZxT!xtJqD84bSJkbVLsmyUXk8iE6TVUkrXNR7Xhdi-VbW7E

Xhorse VVDI PRO 3.4.0 Firmware 1.2.2 new feature:

* This version DON'T need update firmware

+ Add Porsche BCM (1L15Y/2M25J/5M48H) options

+ Add MC9S12XEQ512,MC9S12XET512 options in <2-MCU>-->Motorola

+ Add BENZ EIS-W203 in<4-IMMOBILIZER>

* Fix some display BUGs in English Version

* Change the name of upgrade button as "Start Firmware Upgrade"

* Change the Voltage name as "VCC","VPP"

How to update VVDI Pro programmer software & firmware?

Open VVDI Pro software

Click “Upgrade” tab

Then come to VVDIProg Update menu. You are able to check software version (Tip Information) and firmware version (Device Information).

(NOTE: Newest VVDI Pro V3.4.0 does not need to update firmware)

8/30/2015

Xhorse VVDI2 VVDI II vs. Xhorse VVDI Prog Programmer

Xhorse Tech has newly released two powerful OBD tools: VVDI Prog and VVDI 2. What’s the difference between VAG Vehicle Diagnostic Interface VVDI2 and VVDI-Prog?

VVDI2 diagnostic & programming interface

VVDI-PROG programmer:

Major difference:

(detail comparison, please check table below)

VVDI 2 is the update version for VVDI (Item number SV30), it inherited VVDI all features, mainly used to diagnose, programming ECU and keys and so on. VVDI2 added other features:

VVDI2=VVDI options + BMW Multi Tool options+Porsche options+J2534(free)+ Tango(free)+Remote control generation(free).....more other function

While VVDI prog is a newly developed ECU programmer mainly for EEPROM ECU, MCU programming and pin code calculation.

VVDI PROG=（BMW ISN READ）+（EERPOM read)+(mcu read MOTO 9S12,5M48****)+PIN Code Calculation(more pin coder Algorithm ,than 40 type)

In short, VVDI 2 is a comprehensive OBD tool for diagnose and programming (program ECU and program keys). VVDI Prog turns to be an car ECU programmer.

What’s the difference of the VVDI 2 and VVDI Prog?

Item	VVDI 2	VVDI Prog V2.1.0
Update	Update online	Update online
Language	English only	English/Chinese
Function	Diagnose Odometer correction ECU programming Key programming Key learn Etc	Program EEPROM Program MCU Program ECU Pin code calculation
Operating system	Windows XP/Windows 7	Windows XP/Windows 7
Price	€2,110	€385

8/26/2015

2015 VVDI2 VVDI PROG 2 VAG Vehicle Diagnostic Interface

VVDI PROG 2--- the second generation VVDI (VAG Vehicle Diagnostic Interface) is soon available in eobdtool.co.uk. VVDI2 goes beyond than VVDI in function, features, connectors and vehicle coverage etc. If VVDI is a VAG locksmith tool, the VVDI2 is a comprehensive locksmith device.

VVDI2=VVDI options + BMW Multi Tool options+Porsche options+J2534(free)+ Tango(free)+Remote control generation(free).....more other function

Some test working picture displays:

VVDI 2 Special Function:

Including all VVDI functions, improved and more stable
More vehicle coverage, multi Immo functions
New added plug-in function and reserved connectors to include all VVDI functions

VVDI PROG includes all the VVDI functions, The function of Tango, Remote control generation and chip identification is improved, And also the coil’s stability has been enhanced.
More ever, Users do no need to connect Xhose VVDI PROG 2 with computer or other devices to identify chip or detect remote frequently.

Add more vehicle models
VVDI supports diagnostic function only for VAG groups, But VVDI PROG has achieved multi brand vehicle diagnosis and supports part of vehicle immo programming function and software online upgrade.

VVDI PROG can replace lots of customized devices. Users do not need to purchase specific OBD tool for specific vehicle makes which will save you a lot.

Plug-in function, reserved connectors
VVDI 2 can act as a multifunction programmer to connect plug-ins, and read & write IC and CPU data.
Can read and write Benz IR key, Can program key for old and new Mercedes–Benz, Can connect BMW plug to realize OBD function, And meanwhile reserve some connectors for further uses.

The core function is to detect the remote control frequency;
Automatically identify chip type
Support multi-function on VW vehicles
Read BMW ISN
Key programmer
Remote control programmer

J2534 compatible adapter

1.Detect key frequency, automatically identify chip type
The test result can show on the main unit display, no need to connect computer

2. Support VAG vehicle diagnostic function
Read & write Immo4/Immo5 system
Learn key
Program BCM remote
K-Line instrument immobilizer box
Correct odometer
Program control unit
Unlock Immo1/Immo2 firmware protection
Support data manipulation tools

3.Support OBD functions on BMW vehicles.
Correct odometer
Generate key
Unlock Key
Fix CAS4 EEPROM key programmer
Generate specialized chips
Immobilizer data processing tool
Other key tools
Generate remote control

4. Passthru J2534 Introduction

With built-in switch matrix, it supports third-party diagnostic software including: ODIS, Toyota TIS techstream etc. To perform VVDI2 diagnostic function, third-party diagnostic software should be compatible with J2534 function.

VVDI 2 superiority
VVDI technician has devoted themselves to VVDI free update online and update service in the pass five years. This is what VVDI has been widely respected and ranked as a power tool.

There is no doubt that the more power and high-end configuration VVD2 will inherit the fine traditions. Apart from free update online service and system optimization, more powerful functions and vehicle models (Like Porsche) will soon be available via update. And other more functions, you name it…

VVDI2 goes beyond than VVDI in function, connectors and vehicle coverage etc. After all, VVDI belongs to locksmith tool while VVDI2 becomes a comprehensive locksmith device.